Multi-line 2 ASC Application Software series 4.x
You’re about to download Multi-line 2 ASC Application Software series 4.x
You have chosen to download our software.
Within a few seconds, you will receive an email containing a download link.
Having trouble using the software? Please contact support@deif.com.
Best regards,
DEIF A/S
The software is subject to copyright DEIF A/S
By following the above mentioned link and downloading the file you automatically accept DEIF A/S copyright and license agreement (EULA). The license agreement can be found on www.deif.com/software
This software applies to the following DEIF products:
- ASC-4 Battery - Automatic Sustainable Controller
- ASC-4 Solar - Automatic sustainable controller
- ASC-4 Battery Single Controller - Automatic sustainable controller
- ASC-4 Solar Single controller - Automatic sustainable controller
You’re about to download 4.27.2
The main changes implemented since the last version are as follows:
PM compatibility version 1.33.0
Corrections:
• Corrected issue where multiple batteries would not share the allowed charging power when peak shaving charging limit is used.
• Switch from AUTO to SEMI on another device could cause a breaker to open and stop in rare cases.
• Fixed an issue where PV protocol for Canadian CSI 3PH did not start correctly.
Ver. | Date | Description |
---|---|---|
4.27.2 |
01/03/2024 |
PM compatibility version 1.33.0 Corrections:
|
4.27.1 |
09/02/2024 |
PM compatibility version 1.33.0 Corrections. • Sungrow LC200 Powerstack. PF is now calculated based on ESS P and Q instead of S measurement.
|
4.27.0 |
19/12/2023 |
PM compatibility version 1.33.0 New features:• Added support for using CAT EMCP 4 controllers directly as power meter.
Changes:• Updated the Ausar ESS protocol to make more data available and acknowledge faults in the system when the "ESS shutdown" alarm is acknowledged.
Corrections.• Split the "Secure Elite XXX" power meter into two protocols: "Secure Elite 100/300" and "Secure Elite 440/500". This was done to correct a power scaling issue. |
4.26.1 |
26/10/2023 |
PM compatibility version 1.30.0
Corrections
|
4.26.0 |
10/07/2023 |
PM compatibility version 1.30.0 New features
Changes
Corrections
|
4.25.0 |
09/02/2023 |
PM compatibility version 1.29.0 New features:
Changes:
Corrections:
|
4.24.0 |
24/11/2022 |
PM compatibility version 1.28.0 New features:
Changes:
Corrections:
|
4.23.1 |
15/09/2022 |
PM compatibility version 1.25.0 Corrections:
|
4.23.0 |
31/08/2022 |
PM compatibility version 1.25.0 New features:
Changes:
Corrections:
|
4.22.0 |
03/05/2022 |
PM compatibility version 1.25.0 New features:
Changes:
Corrections:
|
4.21.0 |
18/02/2022 |
PM compatibility version 1.25.0 New features: Changes: |
4.20.0 |
09/12/2021 |
PM compatibility version 1.24.2 New features:1- Sungrow LC100 BCU protocol added. Changes:1- Renamed "Ginlong Solis" PV protocol to "Solis (Ginlong)". |
4.19.0 |
22/11/2021 |
PM compatibility version 1.24.2 New features:
Changes:
Corrections:
|
4.18.0 |
20/09/2021 |
PM compatibility version 1.24.1 New features:
Changes:
Corrections:
|
4.17.1 |
16/07/2021 |
PM compatibility version 1.24.1. Corrections:1- Corrected that the EVVO PV protocol did not send control telegrams to control the active power of the inverter. |
4.17.0 |
28/06/2021 |
PM compatibility version 1.24.1. New features:
Changes:
Corrections:
|
4.16.0 |
08/04/2021 |
PM compatibility version 1.23.0. New features:
Changes:
Corrections:
|
4.15.1 |
25/02/2021 |
PM compatibility version 1.22.0. Corrections:
|
4.15.0 |
30/11/2020 |
PM compatibility version 1.22.0. New features:
|
4-14-2 |
29/10/2020 |
PM compatibility version 1.20.0 Corrections:
|
4.12.0 |
19/03/2020 |
PM compatibility version 1.16.0. New features:
|
4.11.3 |
28/01/2020 |
PM compatibility version 1.16.0 Corrections:
|
4.11.2 |
24/01/2020 |
PM compatibility version 1.16.0 Corrections:
|
4.11.1 |
31/10/2019 |
PM compatibility version 1.16.0. Corrections:
|
4.11.0 |
11/12/2018 |
PM compatibility version 1.16.0 New features:
Corrections:
|
4.10.1 |
16/04/2018 |
Corrections:
|
4.10.0 |
20/03/2018 |
PM compatibility version 1.16.0 New features:
Corrections:
|
4.05.2 |
12/01/2018 |
Corrections:
|
4.05.1 |
02/01/2018 |
PM compatibility version 1.15.0
|
4.05.0 |
30/11/2017 |
PM compatibility version 1.15.0 New features:
Corrections:
Changes:
|
4.04.0 |
05/10/2017 |
PM compatibility version 1.15.0 New features:1- Support of HiQ inverter. |
4.03.1 |
09/05/2017 |
PM compatibility version 1.15.0 Corrections:
|
4.03.0 |
03/04/2017 |
Version 4.03.0 New features:
Changes:
Corrections:
|
4.02.0 |
21/12/2016 |
PM compatibility version 1.15.0 New features:
Changes:
Corrections:
|
On this page, you can download software updates for your product(s) and help yourself to various utility tools and add-ons that will assist you in setting up, detecting faults and configuring your product(s).
Please be advised that not all of our products can be updated by the user. Nor do all of our products come with a utility tool. Consequently, the list on this page cannot be considered an overview of our product programme.
DEIF will register your download along with the used e-mail address for the purpose of sending out information on future updates, if requested.
DEIF cannot be made responsible for any consequences of failed product updates or use of utility tools. Nor can DEIF A/S be made responsible for consequences of changes in behaviour of products due to a software upgrade. It is always the responsibility of the user to ensure correct set-up and configuration before commissioning. Please study the version log of the software before updating the product.
Licence agreement for software downloaded from www.deif.com
Downloaded software remains the property of DEIF. The software may not be distributed for commercial purposes, changed or reused in full or in part or sold to any third parties.
The latest versions for full functionality
As always, we recommend that you install our offered improvements to fully utilise your DEIF product.
All improved software can be downloaded at your convenience at www.deif.com under “Software”.
Should you have any questions or experience problems finding the relevant software for your product, please feel free to call DEIF A/S at +45 96149614 or your relevant local DEIF office. Alternatively, we are always ready to assist you, if you send an e-mail to support@deif.com.